加入收藏    | 设为首页     |     联系方式
精品展示
产品中心
联系方式
联系人:冯顺国
电 话:0512-50109099
手 机:13915753620
传 真:0512-50115803
地 址: 苏州市尚轻路36号
邮 编:215300
当前位置: 主页 > 热流道温控箱 >
热流道温控箱           
详细介绍如下:
一、温控箱使用前的确认事项:    
 
    温控箱在连接和使用前,必须确认以下事项,以确保避免因人为原因造成温
控箱的损坏和发生人身事故:
1、检查模具上的热电偶和温控卡上设定的热电偶类型是否一致,即“J”型或“K”型
    必须一致。
2、检查模具上热流道的接线方式和温控箱上的接线盒的接线方式是否一致,尤其
    是热电偶的正负极是否一致。
3、检查配备的电缆线是否适用于此温控箱,接线盒是否匹配,里面的电线和热电
    偶线是否匹配。
4、检查温控箱的输入电源线接线是否正确。
5、检查热流道加热器的电阻和绝缘性,然后检查热电偶是否短路或断路。
6、模具装到注塑机上后连接电缆。
7、检查温控箱的总电源开关和每一组的开关是否关闭,应该事先全部关闭,以避
    免一旦电源接错烧毁温控箱或热流道之热电偶。
8、检测温控箱所接输入电源是否适合温控箱,然后连接好电缆。
9、确保牢固连接好温控箱的接地线。
10、打开电源总开关。
11、打开单组开关:先打开一组,然后再一组组地逐渐打开,这样确保如果接错
      线的话,只是烧掉一组温控卡或一组热电偶。如果有异常声音或显示,请不
      要继续打开其他的温控卡,应立即检查各部分接线。
12、将每组设定到所需要的温度。
13、检查是否达到所需温度以及稳定性。
14、特别注意:在拔插温控卡时一定要先将温控箱电源关闭。
  
  
 
     使用环境温度:   0°C----55°C
     感温器类型:       J型或K型热电偶
 
     控温范围:           0°C----537°C(0-999? F)
 
     控温精度:          ±1°C
     控制输出形式:    可控硅(Triac)输出
 
     输出:            AC220V/15A  3600W
     输入电源:            AC85----400V 50/60Hz
 
注:
 
1、插卡式温控箱1-30点均有成品现货;32点以上需定做。
 
2、温控箱所用配件:德国SIEMENS断路器,台湾进口风扇,意大利GW连接器。
 
3、温控箱接线方式:1、2加热圈3、4(3+,4-)热电偶;可按客户要求接线。
 
4、温控卡、时序卡、温控箱、时序控制器均可做贴牌,或按客户要求定单生产。
First, the temperature control box before the use of the confirmation:
Temperature control box in connection and use, must confirm the following matters, in order to ensure that the cause of the person to avoid temperature
Damage to the control box and personal accident:
1, check the thermocouple on the mold and the thermocouple type is consistent, that is, "J" or "K" type
Must be consistent.
2. Check the connection mode of hot runner on the die and the connection way of the box on the temperature control box.
Is the thermocouple positive and negative poles are consistent.
3, check with the cable is applicable to the temperature control box, junction box, inside of the wire and power
Even if the line is matched.
4, check the temperature control box of the input power cable wiring is correct.
5, check the resistance and insulation of the hot runner heater, and then check whether the thermocouple short circuit or circuit breaker.
6, die attached to the injection molding machine to connect the cable.
7, check the temperature control box of the total power switch and the switch of each group is closed, it should be closed in advance to avoid
Once the power supply is connected to the fault of the thermal control box or hot runner thermocouple.
8, detection of the temperature control box is connected to the input power supply is suitable for temperature control box, and then connect the cable.
9, to ensure that the grounding wire firmly connected to the temperature control box.
10, open the main power switch.
11, open a single set of switches: first open a group, then a group of gradually open, so as to ensure that if the wrong
Line, only to burn a group of temperature control card or a group of thermocouple. If there is an abnormal sound or display, please do not
To continue to open the other temperature control card, should immediately check the various parts of the wiring.
12, each set to the required temperature.
13, check whether the required temperature and stability.
14, note: in the plug temperature control card must first be temperature control box power off.
Using ambient temperature: 0 degrees C----55 degrees C
Type of temperature sensor: J type or K type thermocouple
Temperature control range: 0 degrees C----537 degrees C (0-999? F)
Temperature control accuracy: + 1 degrees C
Control output form: silicon controlled (Triac) output
Output: 3600W AC220V/15A
Input power: 50/60Hz AC85----400V
Note:
1, plug temperature control box 1-30 has finished 32 points more than the required custom spot.
2, temperature control box with accessories: Germany SIEMENS circuit breaker, Taiwan imported fans, Italy GW connector.
3, temperature control box wiring way: 1, 2 heating cycles 3, 4 (3+, 4-) thermocouple; according to customer requirements wiring.
4, temperature control card, timing card, temperature control box, a timing controller can do OEM, or according to customer requirements and production orders.
 


最近更新: 2016-01-07 20:03
上一篇:格润泰热流道温控箱

下一篇:热流道温控箱


Copyright © 2000-2015 格润泰科技有限公司 版权所有